CS-1 uprights are sold in pairs, in 236 or 204 cm, made of 3 mm steel with a 75 x 75 mm section and 2.5 cm holes laser-numbered every 5 cm.
Technical specifications of the CS-1 uprights
- Height: 236 cm or 204 cm
- COLOURS: Black or clear coat steel
- Contents: 2 uprights
- Section: 75 x 75 mm
- Steel: 3 mm thick, 11 gauge
- Holes: 5 cm spacing, 2.5 cm diameter, laser-cut numbering
- Compatibility: CS-1 range accessories and uprights
Two uprights to grow your CS-1 rack
The CS-1 range is built on a simple principle. 75 x 75 mm steel tubing, one single hole spacing and accessories that mount anywhere. You do not pick a fixed rack, you build your own.
This pair of uprights is the basic building block of that logic. You add it to widen your cage, gain height or reconfigure your setup when your needs change, without buying a complete rack again.
Choose your height and your finish
Two heights are available. 236 cm for a full height cage, 204 cm when the ceiling sets the rules, in a basement or under a sloping roof.
On the finish side, black or clear coat steel, to match the rest of your setup.
Built to last
3 mm thick steel in a 75 x 75 mm section. These uprights take the load of heavy training without play or vibration.
Every hole carries a laser-cut number. You find your J-cup setting again from one session to the next without guessing, and you line both uprights up identically first time.
Compatible with the whole CS-1 range
J-cups, safeties, weight storage, bar storage, stations and extensions. CS-1 accessories mount on these uprights. An upright added today stays useful in whatever configuration you run in two years.
Usage and safety tips
- Tighten the hardware to the recommended torque and re-tighten after the first sessions.
- Line both uprights up on the same hole number before every heavy set.
- Anchor or weigh down the cage as soon as you work at maximum load.
- Check the tightness periodically, especially after moving the rack.
Which CS-1 upright should you choose?
Three upright formats exist in the CS-1 range, all in the same 75 x 75 mm section and the same hole standard.
Unique benefits of the CS-1 uprights
- Two heights and two finishes, to suit the ceiling as much as the rest of the setup.
- 3 mm steel in 75 x 75 mm, no play and no vibration under load.
- Laser-cut numbered holes, repeatable settings and instant alignment.
- They grow an existing rack instead of forcing you to replace it.
Frequently asked questions
What are the specifications of the CS-1 uprights?
Set of 2 uprights in 3 mm thick steel (11-gauge), 75 x 75 mm section, holes spaced 5 cm apart of 2.5 cm diameter, laser-numbered, available in 236 cm or 204 cm and in black or varnished steel.
Which height should be chosen?
236 cm for a full-height cage, 204 cm when the ceiling sets the limit, in a basement or under a sloping roof.
What are these uprights for?
To enlarge the cage, gain height or reconfigure the setup when needs change, without buying a complete rack again. They are compatible with all CS-1 accessories: J-hooks, safeties, storage, stations and extensions.
What safety advice applies?
Tighten the bolts to the recommended torque and re-tighten after the first sessions, align both uprights on the same numbered hole before every heavy set, anchor or weigh down the cage at maximum load, and check the tightness after moving the rack.
What is the difference with the other CS-1 uprights?
They all share the 75 x 75 mm section and the same hole standard: these 236 or 204 cm uprights are used to enlarge or raise the cage, the 76 cm uprights for the lower parts and extensions, and the 104 cm compact logo upright for structural reinforcement.
